How to Clean Dyson Airwrap Filter Effectively
Keeping the Dyson Airwrap running at peak performance starts with a clean filter system. Over time, dust, hair, and product residues can obscure airflow, reduce suction, and shorten the device’s life. This guide provides practical, step-by-step instructions to clean or refresh the Airwrap filter and related components using commonly available tools.
The following steps are centered on safe maintenance practices that help preserve suction and improve drying efficiency. A properly cleaned filter system also helps extend the life of the motor and attachment performance, delivering consistent results with each use.
Quick Answer
Regular, gentle cleaning of the Airwrap filter and pre-filter components every few weeks (or more often with heavy use) is recommended. Use a Dyson Airwrap filter cleaning brush to remove debris, rinse if advised by the kit, and replace worn parts with a Dyson Airwrap pre-filter replacement kit when necessary. Keep air paths clear and dry before reassembling.
What You’ll Need
- Dyson Airwrap filter cleaning brush
- Dyson Airwrap pre-filter replacement kit
- Dyson Airwrap cleaning kit with filter brush
- Soft, lint-free cloth
- Warm water (for rinsing, if kit instructions permit)
- Isopropyl alcohol (optional, for stubborn residue; use only as directed)
Before You Start
Prepare a clean workspace and gather the tools. Unplug the Airwrap from power before any maintenance. Remove all attachments and allow internal components to cool if recently used. Check the user manual for any model-specific cautions about cleaning solvents or water exposure. Plan for about 15–30 minutes of work, plus time for drying if you rinse parts. If you notice frayed filters, damaged seals, or persistent odor after cleaning, replace affected parts rather than reusing compromised components.
Step-By-Step: How To Clean Dyson Airwrap Filter
- Disassemble the filter housing: Gently remove the filter cover and lift out the filter assembly according to your model’s manual.
- Inspect for debris: Visually check for hair, lint, and dust clogs on the filter, pre-filter, and surrounding ducts.
- Brush away loose particles: Use the Dyson Airwrap filter cleaning brush to loosen and lift debris from the filter surfaces.
- Rinse or wipe as recommended: If the kit instructions permit, rinse the filter under lukewarm water to remove fine dust; avoid harsh soaps unless specified. Shake out excess water gently.
- Dry thoroughly: Allow all components to air-dry completely in a clean area before reassembly. Do not use heat sources to speed drying unless the manual allows it.
- Clean the pre-filter: If present, remove the pre-filter from the unit and brush it clean. If you have a Dyson Airwrap pre-filter replacement kit, replace worn pre-filters as needed.
- Reassemble and test: Once dry, reattach the filter housing and any pre-filters. Plug in the Airwrap and run a short test cycle without attachments to ensure proper airflow.
- Inspect for improvements: Check that airflow is smooth and loud whines or grinding noises are absent. If airflow remains restricted, consider replacing worn parts with the corresponding kit.
- Schedule regular maintenance: Mark your calendar for routine cleaning every few weeks if you use the device frequently.
- Store properly: Keep the unit in a cool, dry place and avoid reintroducing dust by storing with attachments detached.
- Document replacements: Note the date of every filter or pre-filter replacement to track device health over time.
Troubleshooting
| Symptom | Likely Cause | Fix | Prevention |
|---|---|---|---|
| Reduced airflow after cleaning | Debris remained or filter not fully dry | Re-clean, ensure complete drying before use | Dry thoroughly; avoid reusing damp parts |
| Unusual noise during operation | Loose components or damaged seal | Check seals and re-seat parts; replace if worn | Handle parts gently during assembly |
| Device shuts off unexpectedly | Overheating due to restricted airflow | Improve airflow, clean filter more thoroughly | Clean on a regular schedule; avoid blocking vents |
| Persistent odor after cleaning | Residue buildup or mold in damp parts | Replace contaminated filters; wipe with appropriate cleaner | Allow complete drying; store in dry area |
Common Mistakes
- Using hot water or harsh cleaners on filters unless the manual permits it
- Not fully drying parts before reassembly, leading to mold or odor
- Forgetting to replace worn pre-filters with the appropriate kit
- Rushing the cleaning process and leaving debris in the housing
Avoid these pitfalls to maintain optimal suction and performance over time.
Tips For Best Results
- Schedule cleaning every 2–4 weeks during heavy usage for peak performance
- Keep a dedicated storage spot for spare filters and brushes
- Use the Dyson Airwrap cleaning kit with filter brush for a thorough lift of embedded dust
- When replacing parts, match the kit’s model number to ensure compatibility
- Label replacement dates to track service intervals and plan ahead
Call A Professional
Seek professional help if the Airwrap shows signs of electrical issues, persistent overheating after cleaning, or if any component appears cracked or severely damaged. Do not operate the device when you suspect a faulty power cord or internal wiring. If the device is under warranty and you encounter non-user-serviceable problems, contact Dyson support or an authorized service provider.
FAQ
How often should I clean the Dyson Airwrap filter?
Clean the filter every 2–4 weeks with heavy use, or more often if you notice reduced airflow.
Can I wash the filter with water?
Only wash the filter if the kit instructions allow it; use lukewarm water and ensure complete drying before reassembling.
Do I need a pre-filter replacement kit?
Use a pre-filter replacement kit if the pre-filter shows wear or damage, or if the kit is designed to refresh the whole filter system.
What should I do if the Airwrap still smells after cleaning?
Replace any worn filters and clean surrounding ducts; allow all parts to dry completely before reusing.
Is it safe to use cleaning solvents on the Airwrap filter?
Only use solvents or cleaners recommended by Dyson or the product kit instructions.
Should I lubricate moving parts after cleaning?
No lubrication is typically required or recommended for the Airwrap filter or housing.
Buying Guide
When selecting replacement parts or a cleaning kit, consider size compatibility with your Dyson Airwrap model, the scope of included brushes and replacement filters, and the ease of installation. Noise level is usually minimal when the filter system is clean, but a clogged system can amplify motor noise. Energy efficiency correlates with airflow; a clean filter maintains efficient operation. Controls should be straightforward, with clear indications for when to replace filters. Placement matters: store in a dry, dust-free area away from direct heat. Compare kits by the number of components, compatibility, and replacement schedule to ensure long-term value and minimal downtime.
Leave a Reply